  |
|
Get everything you need to reline your tank.
The Mega Combo contains:
1 - Pint Kreem Tank Liner
1 - Pint Kreem Tank Prep "A"
1 - .5 Pint Kreem Tank Prep "B"
1 - Pint Kreem Tank Cleaner/De-greaser
1 - .5 Pint Kreem Tank Mask
We are currently updating our inventory. We will have more stock at the begining of the year.
Kreem Tank Mask
- Remove dust and dire from all surfaces to be protected. Make sure surface is dry.
- Use a paint brush to apply TANK MASK to the entire surface to be protected and let dry 20-30 minutes. Use two or three coats for maximum protection. Note: Drying time is affected by temperature, humidity and air movement. Apply at 70 degrees F or above. Use of heat or forced air movement will speed dry time. TANK MASK must be dry before using Tank Prep A&B and Tank Liner.
- Remove TANK MASK by peeling or wash with warm, soapy water and sponge or soft cloth.
Pour contents into tank and shake tank for 5 minutes. Be sure that all internal surfaces of the tank have been rinsed with the new tank cleaner.
Drain New Tank Cleaner and rinse with water. The tank is now ready for KREEM’s Tank Prep A & B and KREEM sealer.
Tank Prep-A & B
- Read warning statements on this label and on Part B label.
- Remove the tank from the vehicle, remove any valves and petcocks and stop all outlets.
- Wash out tank with hot soapy water. If the tank is badly rusted and has loose flaky rust add stones or nuts and bolts to agitate to remove loose rust.
- For new tanks, it is important to remove oily protective coating before using Tank Prep. An industrial strength detergent or commercial degreaser/cleaner like KREEM’s New Tank Cleaner/Degreaser or acetone should be used.
- Pour Tank Prep A into tank and add 5 gallons of warm water. Tank Prep A works best when tank is completely full and in contact with all metal surfaces. If this is not possible you should turn the tank to different positions so that the solution has extended contact with all metal surfaces.
- Leave Tank Prep A in the tank until all the rust is dissolved and the metal is etched to a dull gray finish. The time required will depend on the amount of rust in the tank. New tanks can be etched in 4 hours. Rusty tanks will take longer; we suggest overnight.
ALLOW TANK TO VENT. DO NOT ALLOW PRESSURE TO BUILD UP!
- Drain Tank Prep A solution into a plastic container and check tank. If all rust is removed proceed to step B. If rust is still present add saved Tank Prep A solution to tank again until rust is removed.
- Flush the tank with clean water until rinse water no longer foams and all traces of Tank Prep are removed. Remove all excess water.
- Immediately rinse tank interior with full-strength Tank Prep B and agitate to ensure thorough treatment. Drain out all excess Tank Prep B.
- Immediately seal the tank with KREEM FUEL TANK LINER according to label directions.
- Shake or stir well before use. Keep container tightly closed when not in use. Stop all outlets except fill spout.
- Pour Liner into tank and coat entire inner surface by slowly rotating tank in all directions.When all surfaces have been completely coated, a generous excess should remain. Let tank stand for 8-10 minutes with spout open, then close spout and slowly rotate tank allowing excess to re-coat all surfaces. Let tank stand for an additional 8-10 minutes with spout open however, this time on a different side. Repeat this until the tank has the desired coating. Do not allow coating to drain to one area and dry. Drain off excess coating for later use.
- Drain any excess, remove all stops and allow to air-dry in a well ventilated area for at least 24 hours. A nozzle from a low pressure air compressor blowing lightly into the fuel spout and out another opening will greatly reduce setup time.
- For extra protection, air-dry first coat for 6 hours or longer and repeat step 2 of application process.
Kreem Tank Liner
For small tanks (1-5 gallons) use one pint LINER. For larger tanks use one quart per 20 gallon of tank capacity. If the tank contains baffles, be sure to consider the increase in surface area. For spraying or brushing thin with methyl ethyl ketone to desired consistency. Remove the tank from the vehicle, remove any valves and petcocks, and stop all outlets.
Kreem Tank-Prep
Tank Prep-A
Concentrated! Makes 2-1/2 Gallons
Kreem Tank Cleaner/Degreaser
Examples & Dilution Rates:
Light grease & general cleaning dilute 1:10 with water.
Sludge, tar, paint, overspray and equipment and machinery cleanup dilute 1:4 with water.
Asphalt removal and other tough substances use full strength.
Kreem Tank Liner
Kreem Tank Liner is not designed for use in aircraft oil tanks or tanks using a plastic component also not for tanks containing liquids above 238 degrees F.
CAUTION: Surface prep solutions may damage paint.
CONTAINS METHYL ETHYL KETONE DO NOT BREATH FUMES
Avoid contact with eyes; keep from heat, sparks or flame. do not smoke, extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and all other sources of ignition during use and until all vapors are gone. Avoid prolonged contact with skin or prolonged breathing of vapors.
FIRST AID: In case of eye contact flush thoroughly with water. If irritation persists, get medical attention. If swallowed do not induce vomiting. Get medical attention immediately. If vomiting occurs spontaneously, keep victim’s head below his hips to prevent his breathing the vomit into his lungs.
KEEP OUT OF REACH OF CHILDREN
Tank Prep-A
Before using, user shall determine the suitability of the product for intended use, and user assumes all risk and liability whatsoever in connection herewith. The foregoing may not be altered except by an agreement signed by the offices of seller and manufacturer – KREEM PRODUCTS
WARNING: DANGER-MAY CAUSE BURNS – HARMFUL IS SWALLOWED
Contains phosphoric acid. Avoid contact with skin, eyes and mucous membranes. In case of contact, flush with cool water. For eyes, get prompt medical attention. If swallowed, give 1 or 2 glasses of water and call physician immediately.
KEEP OUT OF REACH OF CHILDREN
Tank Prep-B
WARNING STATEMENT: DANGER! FLAMMABLE!
CONTAINS METHYL ETHYL KETONE
Tank Prep-B solution will damage paint.
USE WITH ADEQUATE VENTILATION - DO NOT BREATH VAPORS
Avoid contact with eyes. Keep from heat, sparks or flame. Do not smoke; extinguish all flames and pilot lights and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Avoid prolonged contact with skin or prolonged breathing of vapors.
FIRST AID: In case of eye contact, flush thoroughly with water. If irritation persists, get medical attention. If swallowed not do not induct vomiting. Get medical attention. If vomiting occurs spontaneously, keep victim’s head below his hips to prevent his breathing the vomit into his lungs.
KEEP OUT OF REACH OF CHILDREN
Kreem Tank Mask
CONTENTS: Water, Vinyl-Acetate-Vinyl Alcohol Polymer, Glycerin
Kreem Tank Cleaner/Degreaser
CAUTION: Store below 120 degrees F (49 degrees C) away from heat sources and open flames. Keep out of reach of children.
FIRST AID: In case of eye contact flush thoroughly with water for 15 minutes. If symptoms persist, obtain prompt medical attention.
ALLOW PROPER VENTILATION WHEN USING IN CONFINED AREAS.
The following is made in lieu of all warranties express or implied. Seller’s and manufacturer’s only obligation shall be to replace such quantity of the produce provided to be detective. Neither Seller nor manufacturer shall be liable for any injury loss or damage, direct or consequential arising out of the use or the inability to use the product. Before using user shall determine the suitability of the product for his intended use and user assumes all risk and liability whatsoever in connection therewith. The foregoing may not be altered expect by an agreement signed by the officer of seller and manufacturer - KREEM PRODUCTS.
